Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
Do you find yourself searching for facts concerning Installing A Bathtub?
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly aid you install a new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub and also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly resolve it into its final setting.
Planning for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very involved in How to Install a Bathtub Yourself and I am assuming you enjoyed reading the new article. If you enjoyed reading our page plz don't forget to pass it around. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule Service Pickup
Report this page